How To Use Solar Charge Controller:

-

Hello Friends and welcome to my Blog. In this blog you will be learn how to install a solar charge controller in a few mints.
Let’s gets started
What is a Solar Charge Controller?
        Guys solar charge controller is a device which is basically use for controlling or regulating voltage and current that come from solar "PV" panels to the battery. Actually the solar charge controller protects batteries from overcharging.
Most of the 12 volt solar panel output voltage is about 16 to 20 volts. If you give these high voltages direct to 12 volts battery your battery will be damage from over charging. Most Batteries needs around 14 to 14.5 v to get fully charged.



Little bit about the solar charge controller that I am using:
The controller that i am using is CM3024Z .This charge controller is come in different amperes rating like 10A,20A,30A etc .The one that i am using is 30A .it’s easily available in the market and also cheap in prize.





Connection:
To connect the solar charge controller to your setup is very easy.



Battery connection:
As you can see on the front side of the device six holes with screw on it.
The middle two holes is for the battery connection. Connect the battery positive terminal to the positive point on the charge controller and negative terminal of the battery to the negative point on the controller. Both the positive and negative sign are show on the controller, while in battery red is positive and black is negative. when you connect the 12 volts battery to the charge controller the device will be turn on and you will be see some data on the display.






Solar panel connection:
Now connect the solar panel to the charge controller .same as you connect the battery. Two holes on the left side of the solar charge controller is for the solar panel you will be see a solar sign on it.
Connect the solar panel positive wire to the positive point on the charge controller and negative wire to the negative point on the charge controller.
After successful connection you will be see an arrow blinking on the display from panels towards the battery. Arrow blinking represents the power.



Load Connection:
The left side two holes on the charge controller is for the load connection. From here you can give direct 12 volts DC to your load or give it to an inverter as input. For getting AC power.
An arrow blinking will be show on the screen it means that a load is connected to the solar charge controller.
Now your controller is successfully installed in your solar setup.





Menu Button:
Use menu buttons for showing different data and controlling the input and output power.
From the menu button you can control power on and off.



+ AND - :button are use for increment and decrement the different  values.
Temperature Sensor:
Temperature sensor are use to show temperature 






Without casing the circuit look like this:



 Plastic cover:


Heat Sink on the back side:



                                                                             Video:

                                                        https://youtu.be/yECgD9Mg1PI



Comments

Post a Comment

Popular posts from this blog

MQ-4 Sensor:

-
Image
  MQ-4 sensor is a gas detecting sensor. This sensor is mainly use to detect Methane, and CNG Gas. This sensor also sensing   other flammable gases like Butane and propane. Good sensitivity to Combustible gas in wide range. High sensitivity to Natural gas / CNG. Low sensitivity to smoke, flame. Long life and low cost. Simple drive circuit. There are different MQ series sensor which is used for detecting different gases. List of different   MQ series sensor are given below. MQ-2       Methane, Butane, LPG, Smoke. MQ-3      Alcohol, Ethanol, Smoke MQ-4      Methane, CNG Gas MQ-5     Natural gas, LPG MQ-6      LPG, butane MQ-7      Carbon Monoxide MQ-8       Hydrogen Gas MQ-9        Carbon Monoxide, flammable gasses MQ131     Ozone MQ135     Air Qual...
Read more

MQ-4 Gas Sensor with ESP8266 and Blynk application | IOT Project

-
Image
  MQ-4 Gas Sensor : Monitor your home Gas leakage with your mobile phone. This sensor detects the concentration of methane and CNG gas in the air and outputs its reading as an analog voltage and digital voltage . The concentration sensing range of 300 ppm to 10,000 ppm is suitable for leak detection.  Components:  1:Node Mcu Esp8266. 2:MQ-4 Gas sensor.  3:LED 4:Resistors  5:Buzzer  6:Bread board.  7:Some jumper wires Blynk: Circuit Diagram: Code: #define BLYNK_PRINT Serial #include <ESP8266WiFi.h> #include <BlynkSimpleEsp8266.h> BlynkTimer timer; char auth[] = "Auth Code";                                       //Auth Code from blynk char ssid[] = "WiFi SSID";                                      //your WiFi SSID char pass[] = "Password";  ...
Read more

DIY | How to make a 200 Eggs Incubator at home - XK-W1099 | Home Made Incubator Eggs Hatcher AC/DC

-
Image
  Introduction:                         An incubator is a machine which is use for hatching bird’s eggs. The incubator we design can almost hatch all kinds of bird eggs. Like Chickens, Ducks, Pheasants, Peafowls, Turkeys etc.        The Incubator we design here is Semi Auto. It means that The temperature control   will be automatic while eggs turning will be manual by hand also humidity will be manual .it’s very easy to operate a semi auto incubator successfully .For humidity level control you just need to increase the water surface level will increase humidity level and vice versa . The eggs turning .Two to three times a day will give you a good result. (For good result 8 hours duration between each turning) Components Used in This Project: 1: A Box (Can be made from Wood, fly board, plastic or Aluminum anything that can hold heat inside). 2: Controller I am using XK-W1099 Digital The...
Read more